Red and black OMW Lancer electric skateboards with street wheels on a dry wooden walkway.

Electric Skateboard Noise Troubleshooting: Clicking, Squeaking and Grinding

Hear clicking, squeaking or grinding? Use OMW’s power-off checks to narrow the inspection area and decide whether to clean, maintain or contact support.

Buying an OMW Electric Skateboard: What Else Do You Need? Reading Electric Skateboard Noise Troubleshooting: Clicking, Squeaking and Grinding 12 minutes

Is your electric skateboard making a new clicking, squeaking or grinding noise? Note when it happens, where it seems to come from, and whether braking, steering or acceleration has changed.

Use those details to choose where to inspect first:

  • A repeated click: check around the rotating wheel and drivetrain.
  • A creak while turning: check the trucks and bushings.
  • Noise with changed braking or drive response: stop riding until the cause is assessed.

This guide covers power-off checks of accessible OMW components and the next steps for cleaning, maintenance or support.

When to Stop Riding

Stop riding if the noise comes with any of these symptoms:

  • Braking feels weaker, inconsistent or different from normal.
  • The drive repeatedly skips, slips or loses power.
  • A wheel catches, binds or shows obvious unwanted movement.
  • A belt has missing teeth, cracks, significant fraying or exposed cords.
  • A truck, axle, deck or visible mounting point appears cracked, bent or loose.
  • Steering or stability changes unexpectedly.

Do not ride faster, cross bumps or load the board just to reproduce the sound. What you have already observed is enough to begin an inspection.

Prepare for a Power-Off Inspection

Turn off the board and remote. Disconnect the charger. Secure the board against rolling or tipping, with enough clearance for safe hand rotation.

Keep fingers, hair and clothing away from belt and pulley pinch points. This inspection does not require opening motors, battery enclosures or electrical components.

For the first check, use a flashlight, a dry cloth and a soft brush. Use hand tools only when following the applicable OMW procedure.

Before changing anything, note:

  • Where the sound seems loudest.
  • Whether it repeats with each wheel turn.
  • Whether it occurs while rolling, turning, accelerating or braking.
  • Whether it began after cleaning, a parts change, a rough ride or an impact.

Describe what you observed without guessing at the cause. “Rear area, exact side unclear” is more useful than an unsupported diagnosis.

Clicking, Squeaking or Grinding? Where to Check First

Similar sounds can come from different components. With the board and remote off and the charger disconnected, use this table to choose where to inspect, not to diagnose a failed part.

What you noticed Check first with the power off Findings that need further attention
A click or tap that repeats as a wheel turns Slowly rotate the wheel and look for debris, contact marks or visible wheel, belt and pulley damage Persistent catching, obvious play or damage
Scraping or gritty rotation Check accessible wheel and bearing areas, plus clearance around guards and mounting parts Roughness or rubbing that remains after loose debris is removed
Squeaking or creaking previously heard while turning Inspect the truck assembly, bushings and visible mounting points Displaced bushings, damage, looseness or changed steering
A clunk over uneven ground or after an impact Inspect visible truck, deck and enclosure connections Cracks, deformation or movement at a connection
A new sound on one side after changing wheels Compare that assembly with the instructions for the exact board and wheel kit Rubbing, unwanted wheel movement or an installation you cannot confirm
Noise near a motor with changed acceleration or braking Record the symptoms and photograph visible damage without opening components Keep the board out of use and contact OMW

Sound can travel through the board, so the loudest point may not be the source.

Wheels and Bearings: Grinding, Scraping or Repeated Clicking

Gently turn each wheel by hand through a full rotation where possible. Do not force it past a catch or obstruction.

Watch the gap between the wheel and nearby components. Look for trapped grit, fresh scrape marks or contact with a belt guard or motor mount. Note whether resistance occurs at the same point on each turn.

Check for obvious sideways movement of the wheel relative to its axle. This differs from the whole truck pivoting during steering. If the movement is difficult to identify, record a close-up video for support.

Do Not Judge Bearings by Free-Spin Time

A belt-driven wheel also turns part of the drivetrain, so it may stop sooner than an undriven wheel. Front-to-rear differences alone do not prove bearing damage.

Focus on catching, scraping, unwanted movement and changes from the wheel’s previous behavior.

Brush away accessible loose dirt, then repeat the gentle hand check. Do not tighten the axle nut or add lubricant simply to hide the symptom. Leave sealed bearings intact unless their service instructions specifically describe maintenance.

A smooth hand-rotation check does not rule out a problem that appears only under load. If the original noise came with changed braking, drive response or handling, keep the board out of use even if you cannot reproduce it by hand.

Next step: If grinding, catching or obvious play remains after clearing accessible debris, keep the board out of use and have the wheel assembly checked.

Belts and Pulleys: Clicking, Tapping or Drive Skipping

Rear wheels, visible belts and motors on red and black OMW Lancer electric skateboards.
OMW Lancer rear wheel and drive assemblies. Use this reference view to locate the visible belt and nearby rubbing or debris.

Inspect visible belt edges, teeth and pulley areas for:

  • Missing or damaged teeth.
  • Cracks, significant fraying or exposed cords.
  • Trapped debris.
  • Fresh rubbing marks or visible pulley damage.

Remove only loose debris you can reach without placing fingers between the belt and pulley. If access requires removing a guard, follow the OMW procedure for your setup.

Separate Belt Damage from Repeated Skipping

Visible belt damage: Replace the damaged belt and check the pulleys and installation for a contributing problem.

Repeated drive skipping: Investigate the cause before assuming a new belt will solve it. Tension, alignment, pulley condition and the fitted parts may need checking.

If the noise began after replacing wheels, pulleys or belts, confirm the exact parts installed and compare the assembly with the relevant instructions.

Do not increase belt tension simply to silence a noise. Check tension against the instructions for your setup; extra tension does not correct incompatible parts or other installation errors, and overtightening can cause additional problems.

Use the OMW belt replacement and size guide to match a replacement to your current board, wheels and pulley. Find the belt-tension tutorial in the OMW Video Guide Library for adjustment guidance.

If clicking occurred only during acceleration or braking, record whether you also felt skipping or a change in response. Do not repeat hard acceleration or braking to investigate it.

Trucks and Mounting Points: Squeaking, Creaking or Clunking

Front truck, orange bushings and pneumatic wheels on an OMW Cavalry electric skateboard.
OMW Cavalry front truck and bushings. Inspect visible connections and bushing position before deciding whether an adjustment is needed.

For a creak previously heard while turning, or a clunk over uneven ground, inspect the truck assembly and accessible connections.

Look for:

  • Cracked or bent parts.
  • Bushings displaced from their seated position.
  • Unusual gaps.
  • Fresh contact marks.
  • Visibly loose hardware.

Include accessible deck and enclosure mounting points, but do not open the enclosure.

Wheel axle nuts, truck mounting bolts and kingpin adjustments serve different purposes. Tightening every nut is not a troubleshooting method.

If a specific fastener needs attention, follow the instructions for that location. If the correct adjustment is unclear, photograph the area before changing it. Do not apply lubricant simply because a component squeaks; any treatment should follow its material and service requirements.

Next step: Cracks, deformation, binding or changed steering, or a connection that will not stay secure are reasons to stop riding and contact OMW.

Pneumatic Tires and MAD Wheels: Different Checks

Pneumatic Tires

Measure pressure while the tires are cold, using a suitable gauge.

OMW recommends these cold tire pressures for its pneumatic tires:

  • 150 mm: 30 PSI
  • 175 mm: 36 PSI

These values do not automatically apply to other tires of the same diameter. Use the instructions supplied with your exact tire setup. See the OMW tire pressure, wear and replacement guide for the applicable guidance.

Inspect both sidewalls, the tread, valve area and visible tire seating. Look for cuts, bulges, rubbing or an uneven position on the hub.

Repeated air loss needs investigation even if the tire can be inflated again. Correct pressure also does not rule out a seating, hub, bearing or installation problem.

MAD Polyurethane Wheels

MAD polyurethane wheels do not require inflation. Check for visible cracks, deformation, uneven wear, rubbing and unwanted movement around the wheel assembly.

A click alone does not prove a loose core or damaged bearing seat.

If the sound began after a wheel change, check the specified spacers, hardware and clearance for your board and wheel kit. For driven wheels, also check the matched pulley, belt and alignment. The OMW Video Guide Library includes wheel installation and spacer tutorials.

What to Do After the Inspection

What you found Next action
Accessible loose dirt or debris, with no damage or other warning signs Clean it away, then repeat the visual and gentle hand-rotation checks
An identifiable maintenance or replacement need with a matching procedure Follow that procedure using the specified parts and tools
Persistent catching, grinding, rubbing or obvious play Keep the board out of use until the affected assembly is checked
Structural damage, changed steering, repeated skipping or altered braking Contact OMW before further riding or powered testing
No visible cause and the new noise remains unexplained Report the circumstances rather than replacing parts at random

After maintenance, complete the installation checks in the relevant instructions. A quieter board alone does not confirm that the underlying issue has been resolved.

Electric Skateboard Noise FAQs

Is Some Noise Normal on a New Board?

Belt-drive boards make operating sound. Check a new or changing click or scrape for contact, damage or altered behavior, especially after assembly or a wheel change.

What if the Noise Only Happens at Higher Speed?

Do not repeat a high-speed run to record it. Note the approximate speed range, road surface and conditions you already observed. Tell support about any vibration, instability or change in drive or braking.

What Should I Check if the Noise Started After Changing Wheels?

Start with the changed assembly. Confirm the required spacers, hardware and clearance. On driven wheels, also check pulley and belt compatibility. Do not compensate for incorrect installation with extra belt tension or tighter axle nuts.

The noise only appears when I cross speed bumps or rough ground. Is that serious?

An impact-related clunk can have several causes. With the board off, inspect visible truck, bushing, deck and enclosure connections. Stop riding if you find damage, looseness or changed steering. Do not cross another bump just to reproduce the noise.

Left and right sides sound different. Is that normal?

With the power off, compare accessible debris, rubbing, unwanted wheel movement and installation on both sides. A newly louder or rougher side needs inspection. A sound difference alone cannot confirm that either side is healthy or identify a failed part.

Can I Ride Home if the Noise Suddenly Gets Louder?

Stop safely and inspect. Catching, looseness, visible damage, repeated skipping or altered braking are reasons to end the ride. If the cause remains unclear and you cannot establish that the board is safe to use, arrange another way home.

How to Report an Electric Skateboard Noise to OMW

Email OMW technical support with:

  • Your board model and edition, current wheel setup and order number if available.
  • When the sound started, where it seems to come from and whether it occurs while rolling, turning, accelerating or braking.
  • Recent parts changes, impacts, rough rides, cleaning or water exposure.
  • Clear photos of visible damage, debris, rubbing or loose connections.
  • The checks you completed and any change in drive, braking, steering or wheel rotation.

For an inspection video, keep the board and remote off and the board securely supported. Show the affected area and any gentle hand-rotation check you can perform safely.

Do not hold a phone while riding or recreate a dangerous symptom for the recording. If the noise cannot be captured safely, a written description is enough to begin the conversation.

Leave a comment

All comments are moderated before being published.

This site is protected by hCaptcha and the hCaptcha Privacy Policy and Terms of Service apply.